San Diego Refrigerator Repair
San Diego Icemaker Repair
San Diego Freezer Repair
San Diego Dishwasher Repair
San Diego Waster Heater Repair

Thursday, February 25, 2016

[appliance-repair] Digest Number 2455

2 Messages

Digest #2455

Messages

Wed Feb 24, 2016 1:27 pm (PST) . Posted by:

"Service Specialties" applianceworks

 Why don't you go to a hardware store and buy a universal  120 volt electric heater control and set that up between your heater.  Bill, 707 443-8347 9-7 PT


On Friday, February 19, 2016 8:42 AM, "rhkramer@gmail.com [appliance-repair]" <appliance-repair@yahoogroups.com> wrote:


Update: Oops, I guess the manual I linked to (below) is for the MH1210A which
has a control range of from -50 to 110 degrees C.  The significant difference to
the MH1210F is the control range, which, as stated below is -58℉~194℉.  ATM, I
can't find the manual for the MH1210F.

On Friday, February 19, 2016 11:35:44 AM rhkramer@gmail.com wrote:
> I bought a cheap Chinese digital temperature controller:
>
> MH1210F Digital Temperature Control Controller Thermostat 110V -58℉~194℉
> Delay w/Sensor
>
> You can see the "manual" at:
>
> www.szmeihang.com/uploadfile/201401/20140116231623558.pdf
>
> I bought it to serve as a thermostat in a (homebuilt) combination smoker /
> fermentation "cabinet".
>
> Initially I used it to control the temperature to about 70℉ (with the
> cabinet in my basement) to ferment sauerkraut.  It worked fine.
>
> Recently, I tried to control the temperature to 170℉ to smoke some pork
> ribs. It did not work properly in that, at 163℉, the temperature on the
> display abruptly jumped to 32.1℉.  Because of that, the thermostat would
> no longer control the heat to 170℉, but instead tried to continue to drive
> the temperature from that 32.1℉ back up to 170℉ (well, really 163℉).
>
> Aside: Fortunately (or not), the heating element I use is fairly low
> wattage (400 watts) and would not take the temperature up beyond about 58℉
> on the "revised" attempt to control to 170℉.  I do plan on adding more
> insulation on the outside of the cabinet to achieve the required
> temperature with less energy used.
>
> I've tried writing to the people I bought the unit from and tried searching
> the Internet, but so far have found no help.
>
> I believe the temperature sensor is an RTD device, specified as NTC 25
> degrees C = 10K B3435 +/-1% with 1 meter leads.
>
> Does anyone have any experience with this temperature controller or hints
> of any sort.
>
> One thing I didn't think to do was measure the resistance (with an
> ohmmeter) around the time the display changed from 163℉ to 32.1℉ degrees.
> I may try that experiment sometime soon (without ribs ;-), but if there
> are other suggestions for tests I'd like to do them at the same time.
>
> Thanks!
> Randy Kramer

------------------------------------
Posted by: rhkramer@gmail.com
------------------------------------

All advice on repairs to microwave ovens should only be undertaken by qualified service personnel.
To unsubscribe please send a mail to the following address from the account you recieve this message.
appliance-repair-unsubscribe@yahoogroups.com
------------------------------------

Yahoo Groups Links

Wed Feb 24, 2016 7:52 pm (PST) . Posted by:

rhkramer03

On Wednesday, February 24, 2016 04:24:40 PM Service Specialties
applianceworks@yahoo.com [appliance-repair] wrote:
> Why don't you go to a hardware store and buy a universal 120 volt
> electric heater control and set that up between your heater. Bill, 707
> 443-8347 9-7 PT

Thanks for the reply!

That's a reasonable idea, and might be what I have to do, but I'd like to
figure out the problem with the device I have, even if just to satisfy my
curiosity.

All advice on repairs to microwave ovens should only be undertaken by qualified service personnel.
To unsubscribe please send a mail to the following address from the account you recieve this message.
appliance-repair-unsubscribe@yahoogroups.com
Posted by at

No comments:

Post a Comment

Content

Nothing at all can be a lot more ridiculous as compared to finding a shattered regular utilized home product. It is unquestionably the most sent moment once you find your evryday home use appliances in not working condition. This may probably limit your work as well as daily schedule. Further, when struck in such a scenario, you immediately need to look for an knowledgeable appliance repair service provider to try the home restore task, that can again spoil your other day. Consequently, it is good to test certain things ahead of calling the Las Vegas appliance repairman.







It will be quite previously to call pertaining to home appliance maintenance. There is no need that a machine will become useless after a particular period or even it would quit functioning following your guarantee time period is over. Nonetheless, if it can, go for those tips listed here and then make necessary action.

Set up the engine filters back together again with the dried up wax paper. The next time you are likely to use your washing machine, it's going to smell like vanilla flavouring. You can also alternative this using the scent you want such as lavender or lemon essence.

If your home business office is in disarray, the first task is to undergo everything. I mean every thing. Get yourself some containers or packing containers (depending on the volume of "stuff") and brand them such as so: Document, Shred, Toss, Put Away, Assign, and Action. Go through every thing and allocate it one of the above categories and place the idea in the package. This could require a couple hrs, a whole morning, or even a week depending on how behind you are however do it as well as do it till every very last item is assigned. It's important not to acquire sidetracked. If you come across something should be managed immediately, place it in a specific place to assault when you're finished with organizing for the entire day. Don't commence reminiscing or playing with stuff you haven't affecting awhile, merely stick to your objective until it can be complete!







There is an integrated fuse in many home appliances, which can be located to provide extra security to the power device versus excessive energy. Look at the integrated fuse and modify it together with the new one if neccessary.

When you accomplish DIYs, it's that you are playing. If you need that exact at the same time, then go to a trusted mechanic. Always employ companies that have proven their own caliber to many people customers.